I didn’t even get a push notification on my phone. Victron says itself in the product manual that “the generated alarms are only visible on the VictronConnect app while connected to the SmartShunt or are used to send an alarm signal to a GX device.” I looked into it and learned that the SmartShunt is not equipped with a buzzer. I checked the Victron app and that’s where I saw an in-app alert telling me that my battery capacity was low. Once the battery percentage dropped below 10%, I expected to hear an alarm coming from the SmartShunt. And the time remaining feature is a nice touch when you’re using more or less a constant amount of power. The state of charge told me exactly how much battery percentage I had left. I was able to monitor exactly how many amps and watts my inverter was using at any given moment. This is one of the SmartShunt’s extra features.Įverything worked as expected during the discharge test. While the battery was discharging, I set a low-capacity alarm in the Victron app to go off when the battery’s remaining capacity hit 10%. I discharged the battery at a 0.2C rate (i.e. Since my 12V 100Ah LiFePO4 battery was 100% charged when I set up my SmartShunt, I proceeded to connect a 2000W inverter and perform a discharge test. I’ll cover the extra features a little later on, but know that this is where you go in the app to set those up. The trends reports will delight the battery nerds out there: they show things like voltage, current, and state of charge over time.Īnd then there’s the settings menu, which includes the aforementioned battery settings and settings for some extra features. If you want to dig in further, there are history and trends tabs that show you historical information about your system, such as total amp hours charged and discharged. It shows you a lot of information at a glance, such as voltage, current, state of charge, wattage, and estimated time remaining. Once you connect to the SmartShunt, which must be done every time you open the app, you’ll be taken to the SmartShunt’s “Status” screen. The Victron mobile app is quite robust - and it’s the way you use the SmartShunt - so it’s worth covering it in a bit more detail. Once you’ve input all your settings, your battery monitor is customized for your battery and ready to start monitoring. Also, a quick YouTube search for “victron smartshunt” will yield plenty of excellent videos that will help you dial in the right settings for your battery. But then there are plenty more, things like Peukert exponent and charge efficiency factor, that you can tweak to make the monitor even more accurate for your system.įortunately, Victron gives us a detailed product manual that has guidance on each setting based on battery type. Of course, like any battery monitor, the SmartShunt has the basic settings, like battery capacity and state of charge. Here you’ll see a lot of battery settings, most of which make no sense the first time you see them. Tap the gear icon in the top right corner to go to the settings menu and tap on “Battery”. To complete setup, you need to input your battery settings. Once you’ve connected, you’ll see the SmartShunt’s “Status” screen that displays important specs such as battery percentage, battery voltage, current, and wattage. Locate the SmartShunt in the app’s list of devices and connect to it following the instructions. The SmartShunt has Bluetooth built-in, so you interface with it and adjust settings entirely through the app. To set it up for your system, you download the free VictronConnect mobile app and open it up on your phone. The SmartShunt powers up automatically once you’ve connected everything properly. Tip: Charge your battery bank to 100% before connecting a battery monitor. Once mounted, you follow the instructions for connecting the SmartShunt to your system, which you do in the same way as any other battery monitor. Use a drill and 2 screws to mount the shunt to a wall.Use double-sided mounting tape to tape the shunt directly to your battery.It doesn’t have a screen, so all you have to do is mount the shunt, which can be done in 2 ways: The SmartShunt is by far the easiest battery monitor to install. Victron SmartShunt Review Installation Mounting the SmartShunt can be as easy as taping it directly to your battery.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |